{"product_id":"altronix-eflow104nka8dqm-12-24dc-6a-net-acc-ptc-115","title":"Altronix EFLOW104NKA8DQM 12\u002624DC@6A\/NET ACC\/PTC\/115","description":"Altronix EFLOW104NKA8DQM 12\u0026amp;24DC@6A\/NET ACC\/PTC\/115\n\nAltronix eFlow104NKA8DQM sub-assembly kit converts a 120VAC 60Hz input into eight (8) PTC protected power-limited outputs. Outputs are individually selectable, providing 12VDC or 5VDC up to 6A and\/or 24VDC up to 10A (240W total power) for access control panels, door locks, and ancillary devices. Power outputs can be converted to dry form “C” contacts. Outputs are activated by an open collector sink, normally open (NO), normally closed (NC) dry trigger input, or wet output from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. eFlow104NKA8DQM will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and\/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs. The spade connectors allow you to daisy chain power to multiple LINQ8ACM modules. This feature allows you to distribute the power over more outputs for larger systems. Built-in LINQTM Network Power Management facilitates monitoring, reporting and control of power\/diagnostics.\n\n\neFlow104NB Power Supply\/Charger\nInput\nVoltage: 120VAC, 60Hz, 4.5A max.\nInput Fuse: 6.3A \/ 250V.\n\nOutputs\nVoltage: 24VDC @ 10A.\nAuxiliary: 1A (unswitched).\nProtection: Overvoltage protection. Filtered and regulated.\n\n\nBattery Charging\nType: Sealed lead acid or gel type.\nFuse Rating: 10A @ 32VDC.\nFailover: Upon AC loss, instantaneous.\n\u003ci\u003e(Batteries are sold separately).\u003c\/i\u003e\n\nFire Alarm Disconnect\nSupervised: Latching or non-latching.\nEOL: 10K Resistor.\n\nSupervision\nAC Failure: Form “C” contacts.\nBattery: Form “C” contacts.\nLow DC Power Shutdown: Shuts down DC output terminals if battery voltage drops below 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge.\n\nIndicators LED\nAC Input: 120VAC is present.\nDC Output: Powered.\nBattery: Discharged or not connected.\n\nVR6 Voltage Regulator\nInput\nVoltage: 24VDC from eFlow104NB.\n\nOutput\nVoltage: 12VDC.\nCurrent: 6A continuous.\nOther: Surge suppression.\n\nIndicators LED\nInput: 24VDC is present.\nOutput: Powered.\n\n\nLINQ8ACMCB Network Access Power Controller\nInput\nVoltage: 24VDC from eFlow104NB and 12VDC or 5VDC from VR6.\nInput PTCs: 9A.\n\nOutputs\nPTC protected outputs rated @ 2A per output, power-limited.\nTotal output 20A max.\nAny of the eight (8) PTC protected power outputs are selectable to follow power Input 1 or Input 2.\nIndividual outputs may be set to OFF position for servicing.\nOutput PTCs: 2A.\n\n\nProgramming Features:\nEight (8) Programmable Outputs:\n- Fail-safe, fail-secure or auxiliary outputs.\n- Input controlled or manually controlled through software.\n- High (over) and low (under) voltage and current monitoring by output.\n- Multiple outputs may be programmed to be triggered by a single input.\n- Battery back-up by output.\n\nEight (8) Programmable Trigger Inputs:\n- Normally open (NO).\n- Normally closed (NC).\n- Open collector sink inputs.\n- Wet Input (5VDC - 24VDC) with 10k resistor.\n- Any combination of the above.\n\nOther Programmable Trigger Inputs:\n- Monitor power supply(ies) input for voltage and current limits (high\/low).\n- Input and output current calibration.\n- Programmable timer events.\n- Programmable user levels.\n- Enable or disable alerts by type.\n- Programmable alert reporting delay.\n\nFire Alarm Disconnect\nSupervised: Inactive, latching or non-latching, individually selectable for any or all of the eight (8) outputs.\nEOL: 10K Resistor.\n\nLED Indicators\nGreen AC LED: indicates AC trouble condition.\nGreen BAT LED: indicates battery trouble condition.\nGreen FACP LED: indicates FACP disconnect is triggered.\nFlashing Blue Heartbeat LED: indicates network connection.\nIndividual OUT1 - OUT8 Red LEDs: indicate outputs are triggered.\nOut1 - Out8: Bi-colored LEDs indicate 12 or 24VDC.\n\n\nEnvironmental\nTemperature\nOperating: 0° C to 49° C (32° F to 120° F).\nStorage: - 20° C to 70° C ( - 4° F to 158° F).\n\nRelative Humidity\nRelative Humidity: 85%  +\/- 5%.\n\nBTU\/Hr. (approx.):\n123 BTU\/Hr.","brand":"Altronix","offers":[{"title":"Default Title","offer_id":46151397671108,"sku":"EFLOW104NKA8DQM","price":776.85,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0712\/2649\/1076\/files\/main_ba4bea15-66e8-430b-a10b-946e045517b9.jpg?v=1778870750","url":"https:\/\/avdepot.net\/products\/altronix-eflow104nka8dqm-12-24dc-6a-net-acc-ptc-115","provider":"AV Depot","version":"1.0","type":"link"}